Beckhoff AM8000 Series Operation Instructions Manual Download Page 83

Page: 83 / 123

Technical description

Version: 4.3

───

AM8000 and AM8500

7.2

Feedback

Feedback exchange

The feedback system installed can only be replaced with an identi-
cal system. It is not possible to change the feedback system retro-
spectively.

The table below provides information about system accuracies and
resolutions of the motor feedback systems:

Feedback

Resolution

System accuracy

Comment

OCT, single-turn

OCT, multi-turn

18-bit

± 120 angular seconds ~ 0.03°

Standard:

AM801x – AM8x6x

Standard fan:

AM805x – AM8x6x

Hiperface, single-
turn

Hiperface, multi-turn

18-bit

± 120 angular seconds ~ 0.03°

Standard:

AM807x

OCT, single-turn

OCT, multi-turn

23-bit

± 45 angular seconds ~ 0.0125°

From firmware v2.10

OCT, single-turn

OCT, multi-turn

24-bit

± 25 angular seconds ~ 0.0069°

SIL 2

From firmware v2.10

Resolver

14-bit

± 600 angular seconds ~ 0.17°

Option

Summary of Contents for AM8000 Series




























































































































Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands

Beckhoff AM8000 Series, Operation Instructions Manual

Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands