Beckhoff AM8000 Series Operation Instructions Manual Download Page 79

Page: 79 / 123

Transport and storage

Version: 4.3

───

AM8000 and AM8500

6.2

Transport

WARNING

Do not enter the area below suspended motors

Use suitable means of transport and secure the motor against
falling.

If the motor falls down, this can lead to serious or even fatal acci-
dents.

Avoid hard impacts on the motor

Use suitable means of transport and secure the motor against fall-
ing.

Falling and hard impacts will damage the motor and motor compo-
nents.

6.2.1

AM8x3x to AM8x5x

Transport of the series AM8x3x to AM8x5x without aids.

6.2.2

AM8x6x

Transport of the AM8x6x series with eye slings.

WARNING

Fasten eye sling correctly

Only attach the eye sling to the motor housing. Make sure the
load is balanced. Do not attach the eye sling to the shaft.

Lifting with the eye sling when the load is not balanced can lead
to the motor slipping out and seriously or even fatally injuring
people as well as damaging the motor.

► Attach eye sling 1 to motor housing 2

► Ensure that the eye sling is balanced at both ends of the motor

► Lift the servomotor with a suitable hoist

Summary of Contents for AM8000 Series




























































































































Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands

Beckhoff AM8000 Series, Operation Instructions Manual

Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands