Beckhoff AM8000 Series Operation Instructions Manual Download Page 27 | Manualshive

Page: 27 / 123

background image

Technical data

Version: 4.3

───

27

AM8000 and AM8500

4.2

Data for operation and

environment

Beckhoff products are designed for operation under certain environ-
mental conditions, which vary according to the product. The follow-
ing specifications must be observed for operation and environment
in order to achieve the optimum service life of the products.

Operate the motor only under the specified conditions

Operate motors only under the operating and environmental condi-
tions specified in this chapter. This ensures a long service life and
proper operation.

Temperatures above 40 °C and encapsulated installation can
shorten the service life of the servomotor.

Environmental requirements

Climate category-operation

2K3 according to EN 60721

Ambient temperature during operation

+5 °C to +40 °C, extended temperature range

Ambient temperature during transport

-25 °C to +70 °C, maximum fluctuation 20 K/hour

Ambient temperature during storage

-25 °C to +55 °C, maximum fluctuation 20 K/hour

Power derating

No derating at installation altitudes higher than 1000 m above sea
level and a temperature reduction of 10 K/1000 m.

Derating according to installation altitude

At installation heights higher than 1000 m above sea level and
40 °C:

6 % at 2000 m above sea level
17 % at 3000 m above sea level
30 % at 4000 m above sea level
55 % at 5000 m above sea level

Permissible humidity in operation

95 % relative humidity, no condensation

Permissible humidity during transport and
storage

5 % to 95 % relative humidity, no condensation

«
...
25
26
27
28
29
...
»

Summary of Contents for AM8000 Series




























































































































Reviews:

No comments

Related manuals for AM8000 Series

Brand: YOODA Pages: 7

Brand: Yanmar Pages: 100

Brand: O.S. engine Pages: 20

Brand: Grundfos Pages: 36

marine TM.5.8TS

Brand: Toyama Pages: 88

Brand: O.S. engine Pages: 13

MAX-15CV Series

Brand: O.S. engine Pages: 30

Brand: Lombardini Pages: 57

Brand: Lombardini Pages: 94

Brand: Lycoming Pages: 194

Brand: Volvo Pages: 72

Brand: Robin America Pages: 78

Brand: RIEJU Pages: 37

E ACTION SI 332 AC

Brand: Era Inn Pages: 2

HYPERPOOL SHAKER

Brand: DERRICK Pages: 118

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands