Beckhoff AM8000 Series Operation Instructions Manual Download Page 24

Page: 24 / 123

Product overview

───

Version: 4.3

AM8000 and AM8500

3.5

Intended use

The synchronous servomotors from the AM8000 & AM8500 series
may be operated only for the intended activities defined in this docu-
mentation, taking into account the prescribed environmental condi-
tions.

The components are to be installed in electrical systems or ma-
chines and only put into operation as integrated components of the
system or machine.

The thermal protection contact incorporated in the motor windings
must be analyzed and monitored on a regular basis.

Read the entire drive system documentation:

• This translation of the original instructions

• Original instructions for the AX5000 servo drives and/or the

AX8000 multi-axis servo system

• Complete machine documentation provided by the machine

manufacturer

3.5.1

Improper use

Any use exceeding the permissible values specified in the Technical
data is considered improper and therefore prohibited.

Beckhoff servomotors of the AM8000 & AM8500 series Beckhoff are
not suitable for use in the following areas:

• ATEX zones without suitable housing

• Areas with aggressive environments, for example aggressive

gases or chemicals

The relevant standards and directives for EMC interference emis-
sions must be complied with in residential areas.

Summary of Contents for AM8000 Series




























































































































Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands

Beckhoff AM8000 Series, Operation Instructions Manual

Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands