Beckhoff AM8000 Series Operation Instructions Manual Download Page 20 | Manualshive

Page: 20 / 123

background image

Product overview

20

───

Version: 4.3

AM8000 and AM8500

3.3

Product characteristics

Brushless three-phase synchronous motors

Brushless three-phase synchronous motors have no electrical con-
tact between rotor and stator. This means that the motor has no slip
rings or commutators, which facilitates longer service life of the mo-
tor.

Neodymium permanent magnets

The magnets installed in the motor are permanent magnets.
Neodymium is a hard magnetic material that enables the precise
and highly dynamic positioning of the motors.

Three-phase stator winding

The three-phase winding in the stator reduces the amount of mate-
rial required while maintaining the same electrical output. All phase
angles are 120°.

Electronic commutation in the servo drive

The commutation of the motor is done electronically. The three coil
turns are supplied from a bridge circuit.

Thermal contacts

A thermal contact LPTC-600 is installed to monitor and measure the
winding temperature and to protect the motor against overheating.
This can be read out by the user.

Temperature warning and switch-off:

• Motor warning temperature at 120 °C

• Motor switch-off temperature at 140 °C

«
...
18
19
20
21
22
...
»

Summary of Contents for AM8000 Series




























































































































Reviews:

No comments

Related manuals for AM8000 Series

Brand: Jabiru Pages: 103

TSA 200-100-220

Brand: SCHABMULLER Pages: 56

Brand: CIMCO Pages: 24

Brand: Power Fist Pages: 40

Brand: REXROTH Pages: 86

Brand: Man Pages: 18

Brand: Motorola Pages: 82

Brand: Wilesco Pages: 4

Brand: Chicago Pneumatic Pages: 88

Brand: DETROIT Pages: 64

Brand: LONCIN Pages: 11

Brand: Honda Pages: 133

Brand: rojaflex Pages: 20

Brand: Oemer Pages: 97

Brand: Zenoah Pages: 8

Brand: Hammer Engines GmbH Pages: 35

Brand: Zenoah Pages: 18

Brand: Danfoss Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands