Beckhoff AM8000 Series Operation Instructions Manual Download Page 102

Page: 102 / 123

Electrical installation

102

───

Version: 4.3

AM8000 and AM8500

9.2

Connector assignment

Beckhoff offers various power connectors and feedback connectors.
All connectors are IP65 rated. A protective conductor connection ac-
cording to VDE 0627 is provided on the housing.

9.2.1

OneCableTechnology

The following tables show the connector assignment on the motor
side:

iTec connector

Pin assignment iTec connector

iTec connector

Contact

Function

Core identifica-

tion

Black/1

Black/3

Black/2

Brake+

Brake-

Temp/

OCT+

White

Temperature-/

OCT-

Blue

---

Green/yellow

M23 connector

Pin assignment M23 connector

M23 connector

Contact

Function

Core identifica-

tion

Black/1

Black/2

Black/3

Green/yellow

Temperature-/

OCT-

Blue

Shield

Brake+

Black/5

Temp/

OCT+

White

Brake-

Black/6

Summary of Contents for AM8000 Series




























































































































Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands

Beckhoff AM8000 Series, Operation Instructions Manual

Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands