manualshive.com logo in svg

Beckhoff AG2800, Operating Instructions Manual, Page: 34 / 51

Share
Download
Beckhoff AG2800 Operating Instructions Manual Download Page 34

Mechanical installation

34

 

───

Version: 2.0

AG2800

Carefully clean the inner components of the gear unit

Use  a  cloth  for  cleaning.  Spray  only  the  cloth  with  cleaning  agent
and carefully clean the clamping hub.

Compressed air can damage the seals of the gear unit and clean-
ing agent directly sprayed inside can affect the coefficient of friction
of the clamping hub.

8.1

General tightening

torques

8.1.1

Steel

The specified tightening torques for nuts and bolts are mathematical
values based on the following requirements:

• Calculation according to VDI 2230 (February 2003 edition)

• Friction coefficient for threads and contact surfaces µ = 0.10

• Elastic limit utilization 90%

• Torque tools type II classes A and D according to ISO 6789

The  setting  values  are  rounded  to  conventional  scalings  or  adjust-
ment possibilities:

Bolt size

Quality of the bolts

8.8

10.9

12.9

Tightening torque in Nm

M3

1.15

1.68

1.97

M4

2.64

3.88

4.55

M5

5.2

7.6

9

M6

9

13.2

15.4

M8

21.5

32

37.5

M10

42.5

62.5

73.5

M12

73.5

108

126

M14

118

173

202

M16

180

264

310

M18

258

368

430

M20

362

520

605

M22

495

700

820

M24

625

890

1040

Summary of Contents for AG2800




















































Reviews:

No comments