Beckhoff AG2250 Operating Instructions Manual Download Page 79

Page: 79 / 95

Mechanical installation

Version: 2.8

───

AG2250

8.2

Motor on gear unit

If a motor is included in the scope of delivery:

Motors included in the scope of delivery are pre-mounted.

For optimum performance, we recommend installation on Beckhoff
AM8xxx synchronous servomotors.

Requirements for the attachment of a motor to the gear unit:

• Design B5

• Concentricity and axial run-out tolerance according to EN 50347

• Smooth shaft

• Motor attachment if possible in a vertical position

8.2.1

Clamping hub

The following table provides a description of the clamping hub:

Infographic

Position

Name

Clamping bolt

Clamping ring

Spacer sleeve

Grooved motor shaft

Smooth motor shaft

• Clamping screw according to ISO 4762

Summary of Contents for AG2250
































































































Search results

Summary of Contents for AG2250

Reviews:

Related manuals for AG2250

Brands by name

Popular brands

Beckhoff AG2250, Operating Instructions Manual

Search results

Summary of Contents for AG2250

Reviews:

Related manuals for AG2250

Brands by name

Popular brands