2
Special Requirements - The
installation of a burner shall be
in accordance with the regulations of authorities having
Jurisdiction.
For recommended installation practices in the U.S.
refer to the latest edition of NFPA 31.
(CSA-B139 and CSA-B140 in Canada.
○
Impaired Burner
Performance & Fire Hazard
Do NOT operate the burner beyond speci
fi
cations
outlined in the Table on Page 3.
For applications beyond these limits, consult Beckett
Technical Services at 1-800-645-2876.
NOTE: Some packaged appliances with burners
may be agency listed as a unit to operate beyond
these limits. Consult the appliance manufacturer’s
speci
fi
cations and agency approvals for veri
fi
cation.
y
y
Agency Approvals
UL listed to comply with ANSI/UL296
and certi
fi
ed to CSA B140.0.
Accepted by N.Y.C. M.E.A.
Other approvals may be available and
must be speci
fi
ed at time of order.
○
○
○
To the Owner:
Thank you for purchasing a Beckett burner for use
with your heating appliance. Please pay attention to
the Safety Warnings contained within this instruction
manual. Keep this manual for your records and provide
it to your quali
fi
ed service agency for use in profes-
sionally setting up and maintaining your oil burner.
Your Beckett burner will provide years of ef
fi
cient oper-
ation if it is professionally installed and maintained by
a quali
fi
ed service technician. If at any time the burner
does not appear to be operating properly, immediately
contact your quali
fi
ed service agency for consultation.
We recommend annual inspection/service of your
oil heating system by a quali
fi
ed service agency.
Daily – Check the room in which your burner/ap-
pliance is installed. Make sure:
Air ventilation openings are clean and unob-
structed
Nothing is blocking burner inlet air openings
No combustible materials are stored near the
heating appliance
There are no signs of oil or water leaking around
the burner or appliance
Weekly - Check your oil tank level. Always keep
your oil tank full, especially during the summer, in
order to prevent condensation of moisture on the
inside surface of the tank.
Contents
General Information ....................................................
3
Hazard De
fi
nitions .........................................................................
3
Speci
fi
cations ................................................................................
3
Owner’s Responsibility: .................................................................
3
Service Agency Responsibility: .....................................................
3
Pre-Installation Checklist............................................
4
Combustion Air Supply ..................................................................
4
Clearances ....................................................................................
4
Fuel Supply ...................................................................................
4
Nozzle Pressure ............................................................................
4
Electrical Supply ............................................................................
5
Vent System ..................................................................................
5
Verify Burner Components ............................................................
5
Verify Firing Rate ...........................................................................
5
Verify Air Tube ...............................................................................
6
Stray Light .....................................................................................
6
Dust and Moisture .........................................................................
7
Mount the Burner .........................................................
7
Mount Flange(s) on Air Tube .........................................................
7
Mount Air Tube to Burner ..............................................................
8
Install Nozzle .................................................................................
8
Check Electrode Settings ..............................................................
8
Install Nozzle Line Assembly .........................................................
8
Set “Z” Dimension .........................................................................
9
Insert Burner .................................................................................
9
Fuel Unit By-pass Plug ..................................................................
9
One-pipe Oil System By-pass Loop ...........................................
10
Oil Supply/Return Lines .............................................................
10
Burner Fuel Flow ........................................................................
10
Wire the Burner ..........................................................
11
Typical Burner Sequence of Operation - 7505 Control ...............
11
Typical Burner Sequence of Operation - 7184B Control ............
14
Restricted Lockout .....................................................................
14
Prepare the Burner for Start-up ...............................
15
Start-up checklist ........................................................................
15
Z Dimension ...............................................................................
15
Adjusting Plate Assembly ...........................................................
15
Initial Head Position ...................................................................
16
Initial Air Settings ........................................................................
17
Set Appliance Limit Controls ......................................................
17
Prepare the Fuel Unit for Air Venting ..........................................
17
Start the Burner .........................................................
18
Start Burner and Vent Air From Oil Line ....................................
18
Disable Function ........................................................................
18
Cad Cell Resistance Measurement: ...........................................
18
Operating the Burner ..................................................................
19
Set High-
fi
re Air ..........................................................................
19
Set Low-
fi
re Air ...........................................................................
19
Annual Service ...........................................................................
20
Monthly Maintenance — by Owner ............................................
20
Replacement Parts ....................................................
20
Limited Warranty Information ..................................
24
