background image

®

 BCR130/5-BCR164/6,5-BCR300/12

14  

BEAST CORE RIG OPERATING MANUAL

Problem 

Possible cause

Possible solution

The motor doesn’t work. 

Defective motor.

Defective cable of plug.

Defective switch.

Contact customer service. Never 

repair the motor yourself.

Danger!

GFCI protective switch is not 

switched on, test! 

Have inspected by a electrical 

specialist and replaced if neces-

sary.

Contact customer service. 

Motor makes too much noise.

Damaged windings.

The carbon brushes of the 

machine are worn.

Have the motor inspected by

customer service.

Motor mildly overheats.

Motor overload. 

Motor doesn’t cool sufficiently

Prevent motor overload when 

drilling. 

Remove the dust from the 

motor, so that the cool air can 

flow.

Motor runs. Core bit doesn’t 

rotate.

Gearing defective.

Have the machine inspected by 

the service facility.

Rate of drilling progress 

decreases.

Core bit segments polished.

Water pressure/water flow rate 

too high.

The core is stuck in the core bit.

Maximum drilling depth 

reached.

Core bit defective.

Gearing defective.

The clutch is releasing prema-

turely or slipping.

Sharpen the core bit on a 

sharpening plate while water is 

flowing.

Use the feed lever to reduce the 

water flow rate.

Remove the core.

Remove the core and use a core 

bit extension.

Check the core bit for damage 

and replace if necessary.

Have the machine repaired at a 

service center.

Have the machine repaired at a 

service center.

Motor cuts out.

The core bit has been jammed 

for too long.

Electric power failure.

Electronics defective. 

Free the core bit. Switch the 

motor off and then on again.

Check the plug connections, 

electric power supply and GFCI 

protective switch.

Have the machine repaired at a 

service center.

Water leakage at the water 

swivel or gear housing.

Shaft seal defective.

Water pressure is too high.

Have the machine repaired at a 

service center.

Reduce the water pressure.

Summary of Contents for BCR130/5 BG

















Reviews: