manualshive.com logo in svg

BeamMed Sunlight Omnisense 7000S, User Manual

The BeamMed Sunlight Omnisense 7000S is a revolutionary diagnostic device used for bone health assessment. Ensure proper usage and maintenance of this cutting-edge tool with our comprehensive User Manual. Download it for free from our website manualshive.com and unlock the full potential of this remarkable product.

Share
Download
background image

    

Omnisense 7000S/8000S     

8-1

CHAPTER 8

Patient SOS Measurement

8.1 Preparing the Environment for a Patient

As in any clinical setting, having the correct supplies on hand is 
important for efficient operation. For Omnisense only a few 
items are required:

Table 8.1 Supplies required for use with Omnisense

Item 

Purpose

Ultra-
sound gel

Provides acoustic contact between the 
probe and the site being measured.

Probe 
Caps - 
(Optional)

Used to cover the probe surface in touch 
with the subject skin during measurement, 
for better hygiene. A new cap should be 
placed with every measurement, according 
to a procedure detailed later in this chap-
ter.

Disinfec-
tion tow-
elettes

Used to disinfect probes before use with 
each patient. Towelettes approved for use 
with Omnisense are described in Chapter 
12, "Cleaning and Disinfecting 
Omnisense‚" page 12-1.

Skin 
marker

For marking the scan location.

Station-
ary chair

All SOS measurements are conducted 
with the patient seated. The chair should 
be sturdy, comfortable and without wheels 
or other movability.

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

ABB Relion 670 series Communication Protocol Manual preview
Relion 670 series
Brand: ABB Pages: 66
GE b30 User'S Reference Manual preview
b30
Brand: GE Pages: 242
GE ATS1290 Instruction Manual preview
ATS1290
Brand: GE Pages: 24
Balanced Body Allegro How To Assemble preview
Allegro
Brand: Balanced Body Pages: 3
R.M. Young 32500 Quick Start Manual preview
32500
Brand: R.M. Young Pages: 10
Hacker PROGBOX Manual preview
PROGBOX
Brand: Hacker Pages: 2
J.P. SELECTA SE-100 Manual preview
SE-100
Brand: J.P. SELECTA Pages: 8
Haemonetics PCS 2 Manual preview
PCS 2
Brand: Haemonetics Pages: 134
Hadeco Smartdop 30EX Operation Manual preview
Smartdop 30EX
Brand: Hadeco Pages: 72
NEILPRYDE RS6 Manual preview
RS6
Brand: NEILPRYDE Pages: 55
HANYOUNGNUX STE Series Instruction Manual preview
STE Series
Brand: HANYOUNGNUX Pages: 4
Park House Healthcare WARWICK User Manual preview
WARWICK
Brand: Park House Healthcare Pages: 6
J&M TF2 Operator'S Manual preview
TF2
Brand: J&M Pages: 33
Tascam CC-222SL Technical Documentation preview
CC-222SL
Brand: Tascam Pages: 3
Varytec LED Street Bar 16x3W RGB IP65 User Manual preview
LED Street Bar 16x3W RGB IP65
Brand: Varytec Pages: 9
VARILITE VL1600 PROFILE Quick Start Manual preview
VL1600 PROFILE
Brand: VARILITE Pages: 8
Vari Lite EVENTPROFILE VL800 User Manual preview
EVENTPROFILE VL800
Brand: Vari Lite Pages: 34
Varex Imaging Optica 30 Series User Manual preview
Optica 30 Series
Brand: Varex Imaging Pages: 36

Brands by name

Popular brands

Load more brands