BCDVideo BCD221 User Manual Download Page 84

Page: 84 / 157

Install drives or drive blanks.

Connect the power and data cables

10. Install the access panel

11.

Slide the server into the rack.

12.

Connect each power cord to the server.

13.

Connect each power cord to the power source.

14. Power up the server

The installation is complete.

Riser and riser cage options

Installing primary and secondary risers

Prerequisites

Before installing this option, be sure that you have the following:

• The components included with the hardware option kit
• T-10 Torx screwdriver

Procedure

Power down the server

Do one of the following:

• Disconnect each power cord from the power source.
• Disconnect each power cord from the server.

Do one of the following:

•

Extend the server from the rack

•

Remove the server from the rack

Remove the access panel

Remove the riser cage

Remove the riser board.

Riser and riser cage options

Summary of Contents for BCD221






























































































































































Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands

BCDVideo BCD221, User Manual

Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands