BCDVideo BCD221 User Manual Download Page 82

Page: 82 / 157

Install drives or drive blanks.

10.

Install the secondary rear wall or a riser cage.

11. Cable the drive backplane

12. Install the access panel

13.

Slide the server into the rack.

14.

Connect each power cord to the server.

15.

Connect each power cord to the power source.

16. Power up the server

The installation is complete.

Installing a rear 3LFF SAS/SATA drive cage

Before installing this option, the front bays must be fully populated with 12 LFF drives. High-performance fans
must be installed in all fan bays.

Prerequisites

Before installing this option, be sure that you have the following:

• T-10 Torx screwdriver
• The components included with the hardware option kit

Procedure

Power down the server

Remove all power:

Disconnect each power cord from the power source.

Disconnect each power cord from the server.

Do one of the following:

•

Extend the server from the rack

•

Remove the server from the rack

Remove the access panel

If installed, remove the secondary riser cage. The secondary riser cage is not supported with a three-bay
LFF rear configuration.

Installing a rear 3LFF SAS/SATA drive cage

Summary of Contents for BCD221






























































































































































Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands

BCDVideo BCD221, User Manual

Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands