manualshive.com logo in svg

Bay Networks Remote Annex 2000, Hardware Installation Manual, Page: 71 / 136

Share
Download
Bay Networks Remote Annex 2000 Hardware Installation Manual Download Page 71

3-13

Remote Annex 2000 Hardware Installation Guide

Chapter 3    ROM Monitor Commands

config

The config command displays the Remote Annex 2000’s total number
of ports, total amount of memory, the ID number, the serial number,
the major and minor hardware revision numbers, and the ROM
software revision number. The config command display contains
information describing whether or not Flash ROM is installed. The
command syntax is:

config

The config command display looks like this:

monitor:: config

       REVISION/CONFIGURATION INFORMATION

ROM Software Rev: 0901
Board ID: 56      Board Type: Remote Annex 2000
CPU Type: 486SXLC2   Ethernet Address: 00-80-2D-00-C6-1E
Memory Size: 4 Meg
Flash Size: 2 Meg   Flash ID: 8989
EEPROM Size: 32736

Installed Alternate Interface: ThinNet

ASYNC Config
 Number of Ports: 16
 Max Port Speed: 115.2 Kbps

Summary of Contents for Remote Annex 2000









































































































































Reviews:

No comments