Bay Networks 58000 Installation And Reference Manual Download Page 89 | Manualshive

Page: 89 / 158

background image

Tools and Equipment

893-878-B

3-3

Tools and Equipment

The following tools and equipment are required for installing and removing the
Model 58000 switch:

•

Flat-tip screwdriver to tighten and loosen captive retaining screws

•

Phillips screwdriver to install and remove Phillips screws (if MDAs will
be added or removed from the switch)

•

An antistatic wrist strap and leash to wear when handling switches

CAUTION:

The Model 58000 switch, MDA expansion module, and

MDAs use electronic components that are sensitive to static
electricity. Static discharge from your clothing or other items around
you can cause damage.

Take all possible precautions to prevent static discharge damage
when working with modules. Keep each module in its protective
conductive bag until you are ready to install it. Before you handle a
module, be sure to put on a grounded antistatic wrist strap and leash
and stand on a mat to free yourself of static.

If you lack a grounded antistatic wrist strap and mat, make sure you
stand in one place where you work (so you do not generate static
electricity by friction), and free yourself of static by touching the
metal of a grounded chassis before handling a module.

893-878-B Book Page 3 Monday, May 12, 1997 2:06 PM

«
...
87
88
89
90
91
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Brand: 4IPNET Pages: 97

MatrixPRO-II DVI 16x16

Brand: Barco Pages: 43

Brand: Barco Pages: 5

Brand: SAF Pages: 30

Brand: Vonets Pages: 8

Brand: XtendLan Pages: 228

Brand: Lutron Electronics Pages: 4

InnoMedia MTA 3328-2R

Brand: VoiceLine Pages: 18

Brand: ADTRAN Pages: 20

Brand: DPS Telecom Pages: 80

Brand: NetComm Pages: 34

Full-Rated Router ADSL2+

Brand: PC Concepts Pages: 104

CamCon FCS-4000

Brand: LevelOne Pages: 94

Brand: MikroTik Pages: 5

Brand: Laguna Tools Pages: 24

Brand: Tripp Lite Pages: 2

Brand: Aegis Pages: 7

Brand: Juniper Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands