Bay Networks 58000 Installation And Reference Manual Download Page 75 | Manualshive

Page: 75 / 158

background image

Connecting Model 58000 Switches

893-878-B

2-37

Unsupported Configurations

The following Model 58000 switch configurations are not supported:

•

Where a repeater is placed between two Model 58000 switch ports
configured for auto mode. In this scenario, blocking LattisSpan multicast
packets is not possible; therefore; this design should never be used and
cannot be supported.

•

Installing the Model 58000 switch in a network where the following MAC
address limits are exceeded:

–

1024 MAC addresses per virtual LAN

–

1024 MAC addresses for all of the virtual LANs on a LattisSpan trunk
link

–

8192 MAC addresses per switch community

Exceeding these limits causes performance degradation and can cause
instabilities with the network. Exceeding these limits can also lead to a loss of
connectivity between some devices in the network.

Connecting Model 58000 Switches

Model 58000 switches can be connected to form Model 58000 switch
communities using 100 Mb/s MDA ports. The link that connects two
Model 58000 switches together is called a trunk link.

This section provides information on the following topics:

•

Trunk link creation

•

Address learning across trunks links

•

Redundant trunk links

•

The seven-switch limit between end stations

NOTE:

LattisSpan multicast packets can pass through devices, such as a

fiber optic repeater, that are used to extend the distance of a LattisSpan
trunk link. In this scenario, LattisSpan multicast packets do not have to be
blocked from the repeater or remote bridge.

893-878-B Book Page 37 Monday, May 12, 1997 2:06 PM

«
...
73
74
75
76
77
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Brand: Makita Pages: 2

ADSL2+ Wireless MIMO Router

Brand: Ace Pages: 64

Brand: Dahua Pages: 113

Brand: CAME Pages: 32

Bolide BN-NVR/NX

Brand: GSA Pages: 101

Brand: Idis Pages: 16

Brand: Matrix Switch Corporation Pages: 48

Brand: IBM Pages: 90

Brand: CalAmp Pages: 52

Linktropy MINI-G

Brand: Apposite Technologies Pages: 57

Brand: LevelOne Pages: 10

SECURE BOOT STICK FX

Brand: Ecos Pages: 22

Brand: Westermo Pages: 18

The DSX Value Solution (Japanese) LDX154

Brand: ADC Pages: 4

Brand: Edimax Pages: 40

Brand: Huawei Pages: 15

Brand: Huawei Pages: 9

Brand: Huawei Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands