Bay Networks 58000 Installation And Reference Manual Download Page 25 | Manualshive

Page: 25 / 158

background image

Features

893-878-B

1-3

Features

The Model 58000 10/100 Ethernet Switch has the following features:

•

Double-wide module that fits into the Model 5000 chassis (14 slots) and
Model 5005 chassis (8 slots)

•

16 front-panel 10 Mb/s switch ports:

–

All 16 ports are configurable for half- or full-duplex mode.

–

The first 12 ports (1 through 12) can be connected to the System 5000
backplane in half-duplex mode only.

•

Single front-panel media dependent adapter (MDA) slot to install one of
three types of MDAs:

–

100BASE-FX for support of 100BASE-FX (fiber) links

–

100BASE-TX for support of 100BASE-TX (UTP) links

–

Combination 100BASE-FX/TX for support of both 100BASE-FX and
100BASE-TX links

•

Support by each MDA port of 100 Mb/s transmission rate in half-duplex
mode and 200 Mb/s transmission rate in full-duplex mode (100 Mb/s in
each direction)

•

Switched and dedicated 100 Mb/s transmission (as opposed to shared
100 Mb/s transmission) by both ports on each MDA

•

Support by 100 MDA ports of the Bay Networks flow-control mechanism
(This feature can be disabled through the console port or through SNMP.)

•

Plug-in card slot for installation of expansion modules such as the MDA
expansion module, which enables the installation of up to four additional
MDAs

•

Hot-swap surge protection circuitry that allows transparent insertion and
removal of a module in an operating Model 500x chassis

893-878-B Book Page 3 Monday, May 12, 1997 2:06 PM

«
...
23
24
25
26
27
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Univerge SV8100

Brand: NEC Pages: 44

BiPAC 4500NZ(L)

Brand: Billion Pages: 146

Brand: Rain Bird Pages: 17

Brand: JCG Pages: 2

Brand: National Instruments Pages: 26

Brand: National Instruments Pages: 85

Module SCXI-1503

Brand: National Instruments Pages: 79

Brand: Vanguard Pages: 4

3C410012A - OfficeConnect Remote 531 Access...

Brand: 3Com Pages: 72

Marconi OMS 1200

Brand: Ericsson Pages: 136

Brand: TP-Link Pages: 110

PCH1 T P Series

Brand: Parker Pages: 107

Speedway Revolution

Brand: impinj Pages: 60

Brand: IDT Pages: 292

Brand: IBM Pages: 72

FrameSaver DSL 9788 Router

Brand: Paradyne Pages: 28

Brand: Extron electronics Pages: 19

Brand: Flexwatch Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands