manualshive.com logo in svg

Bay Networks 58000, Installation And Reference Manual

Share
Download
Bay Networks 58000 Installation And Reference Manual Download Page 135

Using the System Configuration Menus

893-878-B

6-29

 

2.

Choose the port you want to change.

The system displays the current type for that port and prompts you to 
change the port type. The current port type is highlighted, and the port 
type options are displayed unhighlighted.

3.

Select the new port type, either auto or feeder.

The system prompts you for confirmation.

4.

Repeat steps 2 and 3 for additional ports.

Modifying Expansion Card Port Flow Control

Flow control for expansion card ports can be enabled only if the 100 Mb/s 
MDA ports are configured for full-duplex mode.

To modify the expansion card port flow control, follow these steps:

1.

Choose Expansion Card Port Flow Control from the Expansion 
Module Port Configuration menu.

An Expansion Module-Switch Port Flow Control menu similar to that 
shown in 

Figure 6-16

 is displayed.

NOTE: 

The new port type is not used until the Model 58000 switch is 

reset. See 

Resetting the Model 58000 Switch

 later in this chapter for 

information about resetting the switch.

893-878-B Book  Page 29  Monday, May 12, 1997  2:06 PM

Summary of Contents for 58000































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands