Bay Networks 58000 Installation And Reference Manual Download Page 113

Page: 113 / 158

Using the System Configuration Menus

893-878-B

6-7

Displaying Startup Messages

The following messages are displayed on the terminal connected to the service
port of the Model 500x chassis, when the Model 58000 switch is powered on or
reset. These messages describe the outcome of the internal switch diagnostics
and ASIC tests.

Bay Networks Model 58000 Ethernet Switch Module

Power-up Diagnostics Version 1.4.3

Created: October 1 1995 12:00:00

System CPU test: PASSED

System memory test (4M): PASSED

Timer test: PASSED

Console port test:..PASSED

CMB Config RAM test (32K): PASSED

NVRAM test (64K): PASSED

Real-time clock test: PASSED

Watchdog timer test: PASSED

ABC test: PASSED

BANSHEE test: PASSED

EPIC test: PASSED

MOCA test: PASSED

DMA test: PASSED

Loopback test: PASSED

End of Diagnostics, entering load stage

893-878-B Book Page 7 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands