manualshive.com logo in svg

baxter Flo-Gard 6301, Service Manual, Page: 143 / 252

Share
Download
baxter Flo-Gard 6301 Service Manual Download Page 143

07-19-B1-729

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL 

11-1

Chapter 11

Chapter 11   

Illustrated Parts Breakdown

Overview

This section includes illustrations and parts lists required to identify any 
replaceable part in the FLO-GARD 6301 Dual Channel Volumetric Infusion 
Pump. Each illustration is keyed to a parts list, which lists each component 
shown in the figure by part number and description. The quantity per 
assembly is also shown. To obtain replacement parts, contact product service. 
The first column shows the figure and item number of each part. The second 
column is the Product Service part number. The third column is the 
manufacturer’s part number, and the last column is the quantity per assembly.

Summary of Contents for Flo-Gard 6301





























































































































































































































































Reviews:

No comments