Baumuller DST2 Series Operating Instructions Including The Safety Instructions Download Page 29

Page: 29 / 30

TAM 00695

DST2-135

– 400 W

10 / 2019

Three-phase synchronous motor, water-cooled

English

Appendix 3: information concerning thrust-bearing motors and oil-features

9.1 Information on permissible axial forces on thrust-bearing motors

Direction of force: from the connection side (DE) to the encoder side (NDE)
Please refer to the Technical Product list DST2-135 - 400W for the axial forces possible in
relation to the speed.

Size

DST2-135

DST2-200

DST2-260

DST2-315

DST2-400

max. perm. axial force
in kN

120

200

270

400

760

Table 9: Permissible axial forces for trust-bearing motors

9.2 Specifications for oil quantities

Size

DST2-135

DST2-200

DST2-260

DST2-315

DST2-400

Oil quantity
in litre

approx. 0.5

approx. 1.5

approx. 2.0

approx. 5.0

approx. 3.0
from length

approx. 5.0

Table 10: Oil quantity for trust-bearing motors

9.3 Specifications for oil service life

We recommend changing the oil when changing the shaft sealing rings, but no later than when
changing the bearing. See

Section 5.2

Mixing oils of different grades or makes is not permitted.

Figure 8: Illustration of trust-bearing motor

Summary of Contents for DST2 Series































Search results

Summary of Contents for DST2 Series

Reviews:

Related manuals for DST2 Series

Brands by name

Popular brands

Baumuller DST2 Series, Operating Instructions Including The Safety Instructions

Search results

Summary of Contents for DST2 Series

Reviews:

Related manuals for DST2 Series

Brands by name

Popular brands