manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 7 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 7

7

of 180

 Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03 

1

D

OCUMENT

 

HISTORY

Revision 

level

State

Modifications

5.11016.01

25.03.2013

Initial document

5.11016.02

05.10.2015

Chapter C.5: Pin-no. in figures added
Chapter 21: Accessories added
Fig. 17 changed
Chapter 15.4.2 text added

5.11016.03

19.11.2018

Software extension BM5-O-SAF-002-xxx-002-#01-yyy-zzz
Chapter 7.1 text changed (in Abs. 4)
Chapter 7.5 warning notices changed and text added
Chapter 7.5.1 and chapter 7.5.2 new
Chapter 7.7.2 new para. 2 
new: Chapter 7.8 software extension SAF-002/3 module
Chapter 7.9 (vorher chapter 7.8) type code extended
Chapter 10.1 and chapter 10.2 para. 2 deleted
Chapter 10.3.1 figure and note new
Chapter 10.4 para. 2 new, figure changed and note new
Chapter 10.4.1 and chapter 10.4.2 new
Chapter 10.5 Abs. 2 new and figure changed 
Chapter 10.5.1 new 
Chapter 10.6 note 2 new and figure changed
Chapter 10.6.1 new 
Chapter.7 figure changed
Chapter 10.7.1 new 
Chapter 10.8 figure new
Chapter 10.8.1 new 
Chapter 10.9 figure new, 3 notes, text new and figure new
Chapter 10.9.1 new 
Chapter 10.10 figure changed, text (para. 5-7) new
Chapter 10.10.1 new 
Chapter.11 figure new
Chapter 10.11.1 and chapter 10.11.2 new 
Chapter 10.12 figure new
Chapter 10.12.1 new 
Chapter 10.13 text changed (in para. 4) and figure new
Chapter 10.13.1 new 
Chapter 10.14 figure new
Chapter 10.14.1 new 
Chapter 10.15 new 
Chapter.11.3 note new 

continue 

 

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments