manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 32 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 32

BAUMÜLLER

NÜRNBERG

GmbH

Ostendstr.

80-90

D-90482

Nürnberg

www.baumueller.de

Made

in

Germany

Doppelachseinheit Safety

640V DC (760 DC)

Eingang:

2*(3* 0 ... 400V AC, 3*3A)

Ausgang:

KB 300%

Betriebsart:

S Nr.: S12345678 Art-Nr.: 06500138

BM5323-SG04-0100-0106-00-16-#01

Typ:

Safety notes

Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03

Baumüller Nürnberg GmbH

32

of 180

7.3

Figure 1:

Example of a type plate of b maXX BM 5000

7.3

Safety notes

WARNING!

m

Operate the Safety Module in combination with controllers, which where released 
by Baumüller Nürnberg GmbH only (see 

Z

Compatibility list

– 

on page 31).

m

The Safety Module may be operated with safety-relevant equipment, as e.g. safe 
I/O-terminals, EMERCENCY-STOP devices as per DIN EN ISO 13850 or with 
safety sensors as per EN 61496 only. 

m

At a total failure of one of the internal drives or of a control element, a short exci-
tation of the drive (IGBT) (also in status STO) may occur. The angular movement 
thus traveled is dependent of the inductor’s position and of the motor’s pole pair 
number. It can reach a maximum of 180°/pole pair number.

DANGER!

Danger due to moving parts!

 

An immediate driver stage supply is caused by the input supply due to a connected 
safety element (emergency-stop device, safety-light grid). A fail of the controller can 
cause an unexpected start-up. Avoid an unexpected start-up during commissioning, 
by providing for external safety components.

Therefore: 

m

Remain at a safe distance from the moving machine parts / installation parts or 
from the moving machine / installation. 

7.4

Operating mode

The module SAF-002 and SAF-003 have an identical hardware. They differ in the number 
of available safety functions. The allocation of the safety functions referring to the module 
types is shown in chapter 

Z

Safety Functions

– 

on page 55. The module supports the 

monitoring of two independent drive axes.

There are two hardware types depending on the module: Daisy-Chain and with separated 
GNDs (see 

Z

Connector Assignment Interface X1

– 

from page 89).

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments