manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 23 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 23

Safety

Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03 

23

of 180

4

4.11 Conduct in the event of danger and accidents

Preventive 
measures

m

Always be prepared for accidents or fire!

m

Keep first aid equipment (first-aid box, blankets, etc.) and fire extinguishers on hand!

m

Instruct personnel in accident reporting, first aid and rescue equipment.

In case of 
emergency: Act 
properly

m

Put the Safety Module out of operation immediately:

n

Always immediately EMERCENCY-OFF at electrical hazards like short-circuits, 
smoke, fire, lightning.

n

At mechanical hazards, if necessary EMERCENCY-STOP until the machine stops. 
Additionally, EMERCENCY-OFF.

m

Keep people out of the danger zone.

m

Introduce first aid measures.

m

Inform the supervisors at the site.

m

Notify a doctor and/or fire department.

m

Clear access routes for rescue vehicles.

4.12 Signs

The following symbols and notification signs are found in the work area. They relate to 
their immediate installation environment.

WARNING!

Injury hazard due to illegible symbols!

In the course of time, stickers and symbols on the Safety Module can become dirty 
or otherwise illegible.

Therefore:

m

Keep all safety, warning and operation signs on the Safety Module in easily legible 
condition at all times.

Electric current

Only qualified personnel may work in work spaces with this marking. 

Unauthorized persons may not touch work equipment bearing this marking.

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments