manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 21 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 21

DANGER!

Live-threatening danger from electrical current!

There is a live-threatening danger at contact with live parts. The damage of the 
insulation or of a single part can be live-threatening.

Therefore:

m

Switch off the voltage supply immediately if there is a damage of the insulation.

m

Only qualified personnel may work at the electrical installation.

m

De-energize the machine for all work with reference to the discharge times (e.g. 
the controller DC-link) and protect against switching it on again.

m

Observe the valid product safety standards when dealing with high-voltage 
equipment.

Safety

Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03 

21

of 180

4

4.8

Special dangers

The residual risks arising as a result of the hazard analysis will be specified in the 
following section.

Observe the safety instructions described here and the warning notices in the following 
chapters in order to reduce health hazards and avoid dangerous situations.

Electrical current

Moving parts

WARNING!

Danger of injury due to moving parts!

Rotating and/or linear moving parts can cause severe injuries.

Therefore:

m

Do not interfere with moving parts during operation.

m

Do not open covers during operation.

m

The mechanical residual energy depends on the application. Powered parts will 
also keep rotating/moving for a certain time after the power supply has been shut 
off. Make sure to provide suitable safety equipment. 

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments