manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 17 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 17

17

of 180

 Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03 

4

S

AFETY

This chapter provides an overview of all important safety aspects for the optimum 
protection of the personnel as well as for safe and trouble-free operation at the machine 
or installation on site. The observance of this is an important precondition for the safe an 
trouble-free operation

4.1

Contents of the operation manual

All persons assigned to work on or with the Safety Module must have read and 
understood that operation manual before beginning work with the Safety Module. This 
also applies if the person concerned has already worked with such a Safety Module or a 
similar Safety Module or has been trained by the manufacturer.

4.2

Alterations and rebuilding of the Safety Module

In order to avoid hazards and ensure optimum performance, neither alterations, additions 
nor rebuilding work may be conducted on the Safety Module unless explicitly authorized 
by the manufacturer.

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments