Baumuller BM5-O-SAF-002 Operation Manual Download Page 147

Page: 147 / 182

147

of 180

Operation Manual

Safety Module for b maXX 5000

BM5-O-SAF-002/3

Document no.: 5.11016.03

CCESSORIES

In this chapter, you will find a list of all the accessories that are available for Baumüller
Nürnberg GmbH's safety module b maXX 5000..

If you have any queries about accessories or suggestions for improvements, Baumüller's
Product Management will be pleased to hear from you.

21.1 List of all accessories

21.1.1 Supplement

Type

Article number

Supplement group 1

00443825

Supplement group 2

00443826

See examples for connecting the Safety Modules

C.5.5 BM5-O-SAF-00x-001-000

(separate grounds, with SO4000)

–

on page 173.

21.1.2 Ferrite ring

Type

Article number

Ferrite ring

00453508

Summary of Contents for BM5-O-SAF-002























































































































































































Search results

Summary of Contents for BM5-O-SAF-002

Reviews:

Baumuller BM5-O-SAF-002, Operation Manual, Page: 147 / 182

Search results

Summary of Contents for BM5-O-SAF-002

Reviews: