manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 10 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 10

Legend

Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03

Baumüller Nürnberg GmbH

10

of 180

2.2

2.2

Legend

Warning notices

Warning notices are marked by symbols in this operation manual. The notices are 
introduced by signal words which express the extent of the hazard.

Comply with the notices under all circumstances and act with caution in order to avoid 
accidents, personal injury and property damage.

DANGER!

....notifies of an imminent dangerous situation which will lead to death or serious 
injuries if not avoided.

WARNING!

....notifies of a potentially dangerous situation which can lead to death or serious 
injuries if not avoided.

CAUTION!

....notifies of a potentially dangerous situation which can lead to minor or slight 
injuries if not avoided.

NOTICE!

....notifies of a potentially dangerous situation which can lead to property damage if 
not avoided.

Recommenda-
tions

NOTE!

....draws attention to useful tips and recommendations as well as information for 
efficient and trouble-free operation.

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments