manualshive.com logo in svg

Baumuller b maXX BMC-M-SAF-02, Operating Instructions Manual, Page: 17 / 120

Share
Download
Baumuller b maXX BMC-M-SAF-02 Operating Instructions Manual Download Page 17

17

of 118

 Operation Manual 

b maXX safe PLC

 BMC-M-SAF-02

Document no.: 5.07020.04

4

S

AFETY

This section provides an overview of all important safety aspects for the optimum protec-
tion of the personnel as well as for safe and trouble-free operation.

4.1

Contents of the Operation Manual

All persons assigned to work on or with the device must have read and understood that 
Operation Manual before beginning work with the device. This also applies if the person 
concerned has already worked with such a device or similar device or has been trained 
by the manufacturer.

4.2

Alterations and rebuilding of the device

In order to avoid hazards and ensure optimum performance, neither alterations, additions 
nor rebuilding work may be conducted on the device unless explicitly authorized by the 
manufacturer.

Summary of Contents for b maXX BMC-M-SAF-02

























































































































Reviews:

No comments