Baumuller b maXX BMC-M-SAF-02 Page 10 Operating Instructions Manual Download

Page: 10 / 120

Legend

Operation Manual

b maXX safe PLC

BMC-M-SAF-02

Document no.: 5.07020.04

Baumüller Nürnberg GmbH

of 118

2.2

Legend

Warning notices

Warning notices are indicated by symbols in this Operation Manual. The notices are in-
troduced by signal words which express the extent of the hazard.

Comply with the notices under all circumstances and act with caution in order to avoid
accidents, personal injury and property damage.

Recommenda-
tions

DANGER!

....notifies of an imminent dangerous situation which will lead to death or serious in-
juries if not avoided.

WARNING!

....notifies of a potentially dangerous situation which can lead to death or serious in-
juries if not avoided.

CAUTION!

....notifies of a potentially dangerous situation which can lead to minor or slight inju-
ries if not avoided.

CAUTION!

....notifies of a potentially dangerous situation which can lead to property damage if
not avoided.

NOTICE!

....draws attention to useful tips and recommendations as well as information for effi-
cient and trouble-free operation.

Summary of Contents for b maXX BMC-M-SAF-02

























































































































Search results

Summary of Contents for b maXX BMC-M-SAF-02

Reviews:

Related manuals for b maXX BMC-M-SAF-02

Brands by name

Popular brands

Baumuller b maXX BMC-M-SAF-02, Operating Instructions Manual

Search results

Summary of Contents for b maXX BMC-M-SAF-02

Reviews:

Related manuals for b maXX BMC-M-SAF-02

Brands by name

Popular brands