manualshive.com logo in svg

Baumr-AG FUJI-MICRO F4200Ri, User Manual, Page: 22 / 25

Share
Download
Baumr-AG FUJI-MICRO F4200Ri User Manual Download Page 22

Fuel-Injected Petrol Powered Inverter Generators 

22 

Specifications 

150cc Engines 

Engine Type 

4-stroke, fuel-injected single cylinder 

Engine Capacity 

150cc 

Fuel Type 

Unleaded non-ethanol 91 RON or better 

Fuel Tank Capacity 

6.5l 

Engine Power Output 

Approximately 3.5HP @ 5000RPM 

Spark Plug Type 

A7RTC 

Spark Plug Gap 

0.7 to 0.8mm (0.028 to 0.032”) 

Valve Clearance 

Inlet: 0.08mm ± 0.10mm (0.003” ± 0.001”) 
Exhaust: 0.1mm ± 0.12mm (0.004” ± 0.005”) 

Engine Oil Type 

SAE 10W-30 automotive engine oil recommended for general use 

Engine Oil Capacity 

Approximately 0.45l (always check level) 

105cc Engines 

Engine Type 

4-stroke, fuel-injected, single cylinder 

Engine Capacity 

105cc 

Fuel Type 

Unleaded non-ethanol 91 RON or better 

Fuel Tank Capacity 

5l 

Engine Power Output 

Approximately 2.8HP @ 5000RPM 

Spark Plug Type 

A7RTC 

Spark Plug Gap 

0.6 to 0.8mm (0.024 to 0.032”) 

Valve Clearance 

Inlet: 0.08mm ± 0.10mm (0.003” ± 0.001”) 
Exhaust: 0.1mm ± 0.12mm (0.004” ± 0.005”) 

Engine Oil Type 

SAE 10W-30 automotive engine oil recommended for general use 

Engine Oil Capacity 

Approximately 0.35l (always check level) 

53cc Engines 

Engine Type 

4-stroke, fuel-injected, single cylinder 

Engine Capacity 

53cc 

Fuel Type 

Unleaded non-ethanol 91 RON or better 

Fuel Tank Capacity 

2.7l 

Engine Power Output 

Approximately 1.6HP @ 5000RPM 

Spark Plug Type 

F7RTC 

Spark Plug Gap 

0.6 to 0.8mm (0.024 to 0.032”) 

Valve Clearance 

Inlet: 0.08mm ± 0.10mm (0.003” ± 0.001”) 
Exhaust: 0.1mm ± 0.12mm (0.004” ± 0.005”) 

Engine Oil Type 

SAE 10W-30 automotive engine oil recommended for general use 

Engine Oil Capacity 

Approximately 0.25l (always check level) 

Summary of Contents for FUJI-MICRO F4200Ri


























Reviews:

No comments