manualshive.com logo in svg

Baumr-AG FUJI-MICRO F4200Ri, User Manual, Page: 19 / 25

Share
Download
Baumr-AG FUJI-MICRO F4200Ri User Manual Download Page 19

Fuel-Injected Petrol Powered Inverter Generators 

19 

Transportation and Storage 

Always ensure that the machine is cool enough to touch before transporting or 
storing. • Petrol/fuel/gasoline is extremely flammable – keep clear of naked flames or 

other ignition sources. • Always transport the machine with the fuel tap and engine ON/OFF switch in the 
“OFF” position. • Drain the fuel tank before transportation or storage. 

Preparing for Transport and Storage 

•

 

Drain the fuel system by allowing the engine to run until it stops. 

•

 

Ensure the fuel tap, engine ON/OFF switch and fuel cap vent are in the “OFF” position. 

•

 

Avoid exposing the equipment to direct sunlight, particularly during transportation. 

•

 

Ensure the equipment is secure the upright during transport.  

•

 

Store the unit in a dry, well-ventilated area and out of the reach of children. 

Long Term Storage 

Follow the normal procedures for storage, then: 

•

 

Remove the spark plug and put 30ml of clean engine oil into the cylinder. Pull the starter rope slowly to 
distribute the oil. Re-install the spark plug. 

•

 

Cover the equipment to protect it from dirt and dust. 

Summary of Contents for FUJI-MICRO F4200Ri


























Reviews:

No comments