Baumer hhs ULT 400 XL Operation Manual Download Page 19

WARNING!
Risk of death for unauthorized persons in the

danger zones and work areas

There are hazards in the working range that only quali-

fied personnel can safely assess and avert. Those who

are unauthorized and do not comply with the described

requirements face the risk of severe injuries and even

death.

Always keep unauthorized individuals away from

the danger zone and work area.

If in doubt, address people and direct them out of

the danger zone or work area.

Always interrupt work as long as unauthorized indi-

viduals are in the danger zone or work area.

The owner must train personnel regularly. Training takes place

annually for safety-relevant aspects. For improved monitoring, a

training record with the following minimum content must be cre-

ated:

n

Date of training

n

Name of trainee

n

Training content

n

Name of trainer

n

Signatures of the trainee and trainer

2.12  Personal protective equipment

Personal protective equipment serves to protect people from

impairments to health and safety during work.

During different types of work, personnel must wear the personal

protective equipment specifically referred to in the individual sec-

tions of this manual.

Protective work clothing

Protective work clothing is defined as close fitting work clothing

with low tear resistance, tight, long sleeves and no protruding

parts.

Safety boots

Safety boots protect feet from being crushed, from falling parts and

from slipping on slippery surfaces.

Unauthorized persons

Training

Description of personal protective

equipment

Safety and responsibility

Personal protective equipment 

04.05.2021

ULT 400 XL

19

Summary of Contents for hhs ULT 400 XL






















































Reviews: