manualshive.com logo in svg

Baumer EAL580 MT Series, Manual

Share
Download
Baumer EAL580 MT Series Manual Download Page 49

 

 

 

 

Baumer_EAx_PROFINET_EN_202011_MNL.docx 

49/74 

www.baumer.com 

11.20 

5.7.  Implementation of system functions for alarm handling 

Make sure that the system components required for alarm handling have been implemented in the project. 
These are in particular OB82 ("I/O Point Fault") and OB86 ("Loss Of Rack Fault"). If these components are 
missing the PLC will enter state STOP in case of an alarm. 
 

 

 

5.7.1. I/O Point Fault OB (OB82) 

The supported channel-specific diagnostic alarms are described under 4.7.1 

„I/O Point Fault OB“ in the 

related chapter of Step7

®

. 

 

5.7.2. Loss Of Rack Fault OB (OB86) 

Loss of Rack Fault OB (OB86) 

is triggered when the encoder is available on the bus after bootup („outgoing 

event“) or when being no longer accessible because of being switched off or disconnected from the bus 
(„incoming event“). 
 

5.8.  Compilation and load of hardware and software configuration 

After complete hardware project configuration and once having entered all parameters the project must be 
compiled („translated“) and exported to the PLC. 
 

5.9.  Restore Factory Defaults 

 

5.9.1. Factory Setup using the Engineering Tool 

The engineering tool may be used to restore default values in the encoder settings. „Restore Factory 
Defaults“ is accessed in the device view under context menu item „Online & diagnostics“.  
 

 

Summary of Contents for EAL580 MT Series











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands