11
After switching on, the extra power is activated for 10 minutes then automatically switches back
on to the maximum normal level 9.
During the time extra power is activated, the power of other hotplates is limited. This is indicated
on the power display by intermittently flashing the selected cooking level and limited power for a
few seconds.
Activating extra powerful setting
• Press the (H) sensor of the required cooking zone, the extra cooking is active. The display
shows “P”.
Premature turning extra powerful setting off
• Press and scroll on the cursor of the wanted zone, until you get to “0” if you want to turn off
the zone, or until the wanted cooking level.
Heat up time automatic
When automatic cooking mode is activated the hotplate will operate at maximum power for a
limited period of time and then automatically switch to the reduced power level to resume
cooking. It may be switched on in any of the hotplates for all power setting
s except for setting “9”
where power is set at maximum all the time.
Automatic cooking mode is activated on any idle hotplate.
• Choose the required continuous cooking level and hold it for 3 seconds.
• The activated heat up time automatic will be displayed through alternating between „A” and
the selected continuous cooking level on the display.
As soon as the parboiling time is over, the preselected continuous cooking level is valid again.
Once the time from the chart below expires, the function is switched off and “A” disappears.
You can also switch the automatic cooking mode off anytime by bringing power setting to “0”.
Power setting
1
2
3
4
5
6
7
8
Max. power
cooking time
48’’
1’44’’ 2’28’’ 3’12’’
4’08’’
1’20’’ 1’68’’ 2’16’’
Bridge Function
With the bridge function two separate cooking elements /inductors with the
same diameter
and
equal power
can be turned on at the same time and controlled with only one operation.
Activating Bridge Function
Whether the two zones are working at a different level, whether they are at level 0:
• Simultaneously press anywhere on the slider (F) of the zones.
• Now the two areas work together, the LEDs to the right of the corresponding displays turn on.
The level is shown on the display of the control zone, in the meanwhile the controlled zone’s
display turns off.
• When this function is active, you can set the timer, the LED lights on near both displays of the
zones
, moreover it’s not possible setting a particularly powerful cooking function.
• If in 10 uninterrupted minutes no cookware is detected on one of the two elements, the bridge
function is automatically deactivated, the uncovered cooking element is switched off and the
covered cooking element remains as the single cooking element switched on with the set
cooking level.
Deactivating Bridge Function
The end of the Bridge Function can be done by repeating the simultaneous selection of both
cooking elements (the same as activation).
If the bridge function is deactivated while in operation, than both cooking elements go to level “0”
and can then be set again.
Warming Function
The warming function is used to keep cooked food warm.
Hence this function can also be used as melting or simmer function.
Activating heating function:
▪ Pressing the special function key (G) of a cooking zone activates the “melting” function. The
first LED is activated.
Summary of Contents for BMEH381I
