background image

16 
 

3 INDUSTRIAL DRIVE 

ELMIRA, ON N3B 2S1 

PHONE: (519)669-4333 

FAX: (519)669-2431 

WWW.BAUMANMFG.COM

 

WARRANTY INFORMATION 

 

One Year Limited Warranty 

If the unit fails to operate within one year from date of purchase because of defects in 
materials or workmanship, Bauman Manufacturing will, at its option, either replace or repair 
such components for the original purchaser.  This warranty does not cover damage resulting 
from accident, misuse or abuse, water, tampering, servicing performed or attempted by 
unauthorized agencies, or units that have been modified in any fashion.  If the components do 
not perform as warranted herein, the original purchaser

’s

 sole remedy will be the repair or 

replacement of the components as provided above.  Bauman Manufacturing products are not 
intended for applications where a failure could result in a costly, dangerous or life-threatening 
situation.  Bauman Manufacturing will not be held responsible for damages or losses greater 
than the cost of the Bauman Manufacturing replacement parts.  In no event will Bauman 
Manufacturing be liable for damages, lost revenue, lost wages, lost savings or any other 
incidental or consequential damages, domestic or international, rising from the purchase and 
use or inability to use the components, even if Bauman Manufacturing has been advised of the 
possibility of such damages.  Except as provided herein, Bauman Manufacturing makes no 
warranties, expressed or implied, including without limitation, the implied warranties of 
merchantability and fitness for a particular purpose, with respect to the components.  All 
warranties for the components expressed or implied, are limited to the warranty period set 
forth above. 
 

WARRANTY SERVICE 

 
In order to obtain the remedy of repair or replacement parts, contact Bauman Manufacturing. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for 1040SI





















Reviews: