Bauer BG 25 Instruction Manual Download

Page: 28 / 183

DESCRIPTION

BG 25 / 2011 /

2254_BG25_en_0000498763_V01

1 - 5

1.2.1.2 Components Description

Table Basic rig components description

Component

Description / Function

Boom

Is a movable link from the machine to the mast
pivot.

Boom cylinders

Are movable connections of the boom to the ma-
chine. They enable adjustment of the machine's
distance to the bore.

Swing mechanism

Enables rotation of the uppercarriage to both
sides.

Crawler drives

Drive the two crawlers forward and reverse.

Counterweights

Render stability to the equipment.

Main winch with main rope

Is used as a hoist for the Kelly.

Auxiliary winch with auxiliary rope

Is used for rigging operations and load handling.

Wedge

Allows changing the distance from mast to bore.

Kinematic triangle (H)

Enables parallel repositioning of the mast.

Mast (upper section / lower section) Provides guidance for the crowd sledge.

Mast prop

Supports the rig during withdrawal of the drilling
tool.

Mast pivot

Is a swivel link between the mast and the boom.

Masthead

Houses sheaves which guide ropes over the mast.

Mast extension (intermediate)

Enables use of longer drilling tools.

Mast extension (lower)

Allows the crowd sledge be positioned further down.

Backstay cylinders

Are movable supports of the mast. They raise and
lower the mast and allow adjustment of the inclina-
tion of the mast.

Uppercarriage

Houses the engine, hydraulic system and controls.

Rope swivel

Prevents rope twist.

Crowd rope tensioning cylinder (S)

Stresses the crowd ropes.

Supporting boom (H)

Enables parallel repositioning of the mast.

Supporting trestle (V)

Is a mount for the backstay cylinders.

Undercarriage

Carries the rig and moves it from one drilling spot
to the next.

Crowd sledge

Runs up and down the mast while carrying the ro-
tary drive and drilling tool.

Crowd ropes (upper / lower) (S)

Transfer force from crowd winch to crowd sledge.

Thrust rod (Z)

Is a distance keeper for the crowd cylinder.

Crowd winch (S)

Generates the crowd forces.

Crowd cylinder (Z)

Generates the crowd forces.

Z) for rig fitted with cylinder crowd

V) for mast lowering to the front

S) for rig fitted with rope crowd

H) for mast lowering to the rear

Summary of Contents for BG 25
























































































































































































Search results

Summary of Contents for BG 25

Reviews:

Related manuals for BG 25

Brands by name

Popular brands

Bauer BG 25, Instruction Manual

Search results

Summary of Contents for BG 25

Reviews:

Related manuals for BG 25

Brands by name

Popular brands