manualshive.com logo in svg

Basler BE1-50/51B-229, Instruction Manual, Page: 25 / 57

Share
Download
Basler BE1-50/51B-229 Instruction Manual Download Page 25

9252000892 Rev A 

BE1-50/51B-229 Functional Description 

i 

SECTION 3 

•

 FUNCTIONAL DESCRIPTION 

TABLE OF CONTENTS 

 

SECTION 3 

•

 FUNCTIONAL DESCRIPTION ........................................................................................... 3-1

 

INTRODUCTION.................................................................................................................................... 3-1

 

RELAY FUNCTIONS AND OPERATING FEATURES .......................................................................... 3-1

 

Sensing Input...................................................................................................................................... 3-1

 

Power Supply ..................................................................................................................................... 3-1

 

Instantaneous Signal.......................................................................................................................... 3-1

 

Time Signal......................................................................................................................................... 3-1

 

Microprocessor ................................................................................................................................... 3-1

 

Power-Off Sensing ............................................................................................................................. 3-2

 

Relay Outputs..................................................................................................................................... 3-2

 

Figures 

Figure 3-1. BE1-50/51-229 Function Block Diagram................................................................................. 3-1 

 

Summary of Contents for BE1-50/51B-229


























































Reviews:

No comments