BASI BFM921 User Manual Download | Manualshive

Page: 17 / 69

background image

BASI

Electromagnetic flowmeter

BF

M921

Operation manual

17

4

Flowmeter configuration

4.1

Main menu

Main menu

is the first menu that appears on power up and can be always reached from all other menus by

pushing the

ESC

key repeatedly. Main menu can be navigated by using four direction arrow buttons.

UP

and

DOWN

buttons are used to switch to next and previous screen in main menu. Pressing

LEFT

button,

user can switch instantly to first main menu screen, by pressing

RIGHT

button to last main menu screen. On

the right side of the screen, navigation bar can be seen, to note user of actual screen.

4.1.1

Overview

This screen is displayed as first after device start as default. Actual flow, total
volume and auxiliary volume is displayed on this screen. Bottom item (auxiliary
volume as default) can be changed to display other types of volume in Setup
menu/General/Display.

4.1.2

Datalogger

This screen displays and provides access to Datalogger function. Datalogger
records can be reviewed using

LEFT

and

RIGHT

buttons.

4.1.3

Status

This screen displays information about device state and configuration. On the first
line, date and time are displayed.

4.1.4

Flow

This screen displays actual and other types of measured flow.

4.1.5

Volume

This screen displays total and other types of measured volume.

«
...
15
16
17
18
19
...
»

Summary of Contents for BFM921






































































Reviews:

No comments

Related manuals for BFM921

Brand: Landis+Gyr Pages: 10

Brand: Labom Pages: 5

Charge Analyzer 711

Brand: 3M Pages: 24

Brand: Badger Meter Pages: 47

Brand: Cannon Pages: 64

Brand: Cannon Pages: 73

Brand: Mahr Pages: 384

Brand: THORLABS Pages: 21

Brand: Omega Pages: 20

Brand: Dakota Digital Pages: 34

Brand: Value Pages: 20

RLACS277RLACS29

Brand: Racelogic Pages: 10

Brand: A&D Pages: 2

Brand: Rinstrum Pages: 2

Brand: IFM Pages: 17

Brand: Chauvin Arnoux Pages: 10

Brand: S&T Pages: 23

HX3 Drawbar Expander Version 5

Brand: KEYBOARDPARTNER Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands