BASI BFM921 User Manual Download | Manualshive

Page: 10 / 69

background image

Electromagnetic Flowmeter

BF

M921

BASI

10

Operation manual

3

Preparing for start up

3.1

Safety precautions

The instrument has been designed according to EN 61010-1:2011. Safety is ensured by the design and by the
use  of  specific  component  types.  Manufacturer  is  not  liable  for  the  damage  caused  by  not  following
instructions  present  in  this  manual  or  modification  of  the  construction  or  replacement  of parts  with  non-
original ones.

3.1.1

Safety symbols used on the equipment

Warning, reference to the documentation

Lucy286

3.2

Inspecting contents of the package

Basic package includes the following items:



Flanged sensor



Electronic Transmitter (integral or remote)



Spare fuse



Operating manual.



Calibration certificate



Software FlowAssistant



USB A-B cable

The flowmeter is delivered ready for use after connecting to the power supply. Please check that it has been
correctly installed according to chapter Mechanical before turning power on. Only a power supply with the
appropriate voltage and frequency must be used, see ordering information in chapter “Power supply”.

Caution!



Only a competent person may connect the flowmeter to the mains power supply.



To prevent accidents, connect main power only after all other wiring has been
completed.



Use only specified voltage and frequency for user flow meter version.



Take national applicable laws and rules into account.

«
...
8
9
10
11
12
...
»

Summary of Contents for BFM921






































































Reviews:

No comments

Related manuals for BFM921

Goldmann AT 870

Brand: Haag-Streit Pages: 20

Brand: JAMAR Technologies Pages: 4

Brand: Jamar Pages: 60

Brand: Magnum Energy Pages: 3

Kotron 805 series

Brand: Magnetrol Pages: 36

Brand: Magnescale Pages: 104

Brand: Magnescale Pages: 44

Ultraprobe 9000

Brand: UE Systems Pages: 25

ULTRAPROBE 10000

Brand: UE Systems Pages: 6

Brand: WATERGUARD Pages: 2

Brand: Lake Shore Cryotronics Pages: 97

Brand: Dwyer Instruments Pages: 189

Brand: Lowrey Pages: 109

Brand: Keller Pages: 4

Brand: DODODUCK Pages: 2

Brand: Spasciani Pages: 26

Brand: X-Rite Pages: 21

Brand: DeNovix Pages: 93

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands