Barrett 4090 HF SDR Page 150 Operating And Installation Manual Download

Page: 150 / 233

138

BARRETT PRC-4090 TACTICAL HF SDR TRANSCEIVER - INSTALLATION

Due of the need to reduce the size of HF antennas so that they can be fitted to a

vehicle, mobile antenna bandwidth becomes quite narrow and hence tuning is

critical. In most cases the only tuning adjustment that can be affected is adjust-

ment to position. Particular attention must be given to the antenna position if

satisfactory performance is to be obtained. Refer to the instructions supplied

with the antenna you have selected.

Antenna Mounting

The antenna mounting must provide a strong secure anchorage for the base

of the antenna. To obtain maximum radiation, the antenna base must be

well bonded electrically to the vehicle chassis. Paint, dirt, rust, etc. should be

removed from the respective fixing points. The mounting point must provide a

low resistance electrical path to the main vehicle metallic structure.

Antenna Feed Cables

Antenna feed cables should be run (as far as possible) away from other vehicle

wiring and especially away from ignition high tension wiring. Where passing

through body panels or internal bulkheads, grommets must be used to protect

the cables. Water-proof connectors must be used when they are outside the

vehicle.

Voltage Standing Wave Ratio (VSWR)

After installation it is recommended that the VSWR of the antenna should be

measured for each channel. The instructions supplied with each antenna will

detail this operation.

Noise Suppression

Noise generated by motor or electrical accessories on the vehicle may cause

objectionable interference to the received signal. This noise enters the receiver

either by means of the battery leads or the antenna system. Providing that the

recommendations concerning battery wiring given earlier in this manual are

followed, noise injected via the battery lead is unlikely to be significant. Most

noise problems result from pick-up by the antenna. Practical cures involve either

preventing the noise from being generated or minimising it from being radi-

ated by the wiring connected to the noise source.

Please note that some newer fuel injected engines emit very strong EMI (Elec-

tromagnetic interference) noise levels across the HF radio band, which is near

impossible to suppress. For these installations, moving the position of the

antenna to another position on the vehicle may reduce the noise effect but full

elimination of noise during engine running may never be achieved. Please note

that this is not unique to the Barrett PRC-4090 transceiver as all transceiver

makes will suffer similarly from the effects of this noise under these conditions.

Summary of Contents for 4090 HF SDR










































































































































































































































Search results

Summary of Contents for 4090 HF SDR

Reviews:

Related manuals for 4090 HF SDR

Brands by name

Popular brands

Barrett 4090 HF SDR, Operating And Installation Manual

Search results

Summary of Contents for 4090 HF SDR

Reviews:

Related manuals for 4090 HF SDR

Brands by name

Popular brands