Barrett 2030 Operating And Installation Manual Download Page 74 | Manualshive

Page: 74 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

Menu Functions

Menus

The menu is divided into two sections, the “Standard Menu” and the “Protected
Menu”. Both sections are used to set or display transceiver parameters. The
“Standard Menu” is available directly to operators as no critical operation
parameters can be changed in this section.

The “Protected Menu” has some critical parameters and needs the operator to
press the menu key for two seconds to enter it.

Note:-

Menu items in both menus can be barred from use, if operationally

required, by using Barrett 2030 PC based programming software.

Navigating the Menus

All sections of the Menus are operated using the similar key press sequences. In
this section when describing the functions available in the Menu system it is
assumed the operator is familiar with the following:-

press

the

key to enter the “Standard Menu” section

press

the

key

for more than 2 seconds

to enter the

“Protected Menu” section

use

the

Scroll keys

to select the menu item you require

then

press

key

Once in the menu item, again use the

Scroll keys

to select a

parameter or enter a value using the numeric or alpha key

When you have the parameter or value required press the

key

Note:-

Due to network operation requirements access to items in the Standard

Menu or Protected Menu may be barred by network administrators during
programming.

74 of 208

«
...
72
73
74
75
76
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Omni Pager OP1097-2

Brand: Silent Call Communications Pages: 2

Brand: OrangeRx Pages: 2

Brand: ferroamp Pages: 10

Brand: Ebyte Pages: 56

Brand: You Ting Technology Pages: 16

Brand: Allmatic Pages: 10

BTL7-V50E-M P-C003 Series

Brand: Balluff Pages: 100

Brand: Tactic Pages: 2

Brand: Topp Music Gear Pages: 4

Brand: Yaesu Pages: 88

Brand: Dat Viet Pages: 18

Digital-Satellite-Receiver

Brand: Dolby Laboratories Pages: 66

Brand: Skytec Pages: 50

Brand: General Measure Pages: 111

DpharpEJX vigilantplant EJX510A

Brand: YOKOGAWA Pages: 49

Brand: Integra Pages: 92

Brand: HobbyKing Pages: 6

Brand: Camille Bauer Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands