Barrett 2030 Operating And Installation Manual Download Page 158 | Manualshive

Page: 158 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

Cloning (Programming) from Another Transceiver

Note:-

Use the transceiver you want

to send the configuration from

for the

following steps

This feature is used to send a copy of the configuration of one 2030 transceiver to
another using a cable (Barrett P/N BCA90024) connecting both transceivers
together via their auxiliary connectors using the RS-232 connection.

Before uploading commences it is necessary to enter the Selcall IDs of the
transceiver that will be loaded.

press

the

key

using the numeric keypad enter Self ID 1 and press the

key

using the numeric keypad enter Self ID 2 and press the

key

158 of 208

«
...
156
157
158
159
160
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: NAIM Pages: 26

Brand: Salora Pages: 7

Brand: Alinco Pages: 48

Brand: Flying Industry Development Pages: 3

Brand: IBR Pages: 20

Brand: Xoro Pages: 90

Brand: Tigo Pages: 3

Brand: Kramer Pages: 2

HYPERVISIONT HV-300 Series

Brand: Raymarine Pages: 66

PowerBox Cockpit

Brand: PowerBox Systems Pages: 30

Brand: Orava Pages: 10

Family Radio Service

Brand: Radio Shack Pages: 2

WiNRADIO A RTEM IS WR- G69DDC

Brand: RADIXON Pages: 133

SRT 4356 PVR Evolution

Brand: Strong Pages: 74

Brand: Kimo Pages: 32

Brand: TANDBERG Pages: 27

Brand: INOR Pages: 2

Brand: Team Electronic Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands