background image

1320/1420/1620 Owner’s-Operator’s Manual 

        2/16/16 

Page 1 of 20 

 

 

 

                                                           

   

THE 

 
 
 
 
 

  

 
 

    MODELS E1320H/1420S/1620B 

                              

 

HYDRAULIC REAR TINE TILLER 

                             OWNER’S/OPERATOR’S MANUAL 

 
 

 

CONGRATULATIONS! 

 

You are now the proud owner of the BARRETO Model 1320 or 1620 tiller. Please take a 
moment of your time to look over the following information. Familiarize yourself with the 
tiller, its characteristics, and method of operation. Pay particular attention to the safety and 
operating instructions. 

 

If you have any questions or need replacement parts in the future, please contact us at 
your convenience.  Our toll-free phone number, fax and email are listed below and parts 
may be ordered through any of these methods. 

 

THANK YOU for your patronage and confidence in BARRETO equipment. 

 

Barreto Manufacturing, Inc. Innovative Equipment Engineered to Last 
66498 Hwy 203, La Grande, OR  97850 
(800) 525-7348 (541) 963-7348 
FAX (541) 963-6755 
E-Mail: 

[email protected]

 

Web Site

http://www.barretomfg.com

 

 
 

Machine Identification Record 

 

Barreto Customer number 

________________________ 

 

Machine model number  

________________________ 

 

Machine serial number   

________________________ 

 

Engine manufacturer      

________________________ 

 

Engine model number    

________________________ 

 

Engine serial number     

________________________ 

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for E1420S





















Reviews: