Barreto 912HM Owner'S Manual Download Page 1

912 Owner’s Manual  

8/31/21  

Page 1 of 16 

 

 

 

 

 THE  

 
 
 
 
 

 

  

                            

MODEL 912HM 

               HYDRAULIC TRENCHER OWNER’S MANUAL 

 

 
 
 

CONGRATULATIONS!  

  

You are now the proud owner of the BARRETO trencher. The OPERATOR’S MANUAL is 
attached to the machine. Please study it and this manual to become familiar with the trencher, its 
characteristics, and method of operation. Pay particular attention to the safety and operating 
instructions to prevent personal injury or equipment damage.   
 
If you have any questions or need any replacement parts in the future, please contact us at your 
convenience. Our toll-free phone number, fax and email are listed below. 
 
THANK YOU for your patronage and confidence in BARRETO equipment. 
 
Barreto Manufacturing, Inc. 
Innovative Equipment Engineered to Last 
66498 Hwy 203, La Grande, OR  97850 
(800) 525-7348    (541) 963-7348 
FAX (541) 963-6755 
E-Mail: 

[email protected]

 

Web Site: 

http://www.barretomfg.com

 

 
 
 
 

Machine Identification Record 

 

Machine model number  ________________________ 
 
Machine serial number   ________________________ 
 
Engine manufacturer      ________________________ 
 
Engine model number    ________________________ 
 
Engine serial number     ________________________ 

 

 

 

 

Summary of Contents for 912HM

















Reviews: