background image

712MT OWNER’S MANUAL                  REVISED   3/4/22                               Page 7 of 15 

    

WARRANTY OF BARRETO MANUFACTURING EQUIPMENT 

 
 
Barreto Manufacturing, Inc. warrants all 

BARRETO

 equipment to be free of defects in material and 

workmanship for a period of one (1) year. All 

BARRETO

 fuel components, fuel tank, cap, lines & 

fittings are warranted for two (2) years.  Warranty period begins on date of delivery to the original 
user. This warranty is in lieu of all other warranties, whether written or implied, and is limited to: 

 

1.  Replacement of parts returned to the dealer and/or factory and determined defective upon 

inspection.  (Replacement for parts to dealers shall be at dealer cost plus shipping 
charges.) 

2.  Time for pick-up and/or delivery, transportation of service calls by dealers is 

excluded.  Manufacturer reserves the right to determine reasonable time required 
for repair. 

 
Warranty does not apply to damage caused by abuse or neglect.  Time and materials required 
for normal maintenance and service are also excluded from warranty coverage. 
 

Engines, engine attached fuel tanks, engine accessories, batteries and tires are warranted by the 
original manufacturer and are not covered by the Barreto Equipment Warranty.

  

 

Wear parts such as dig chains, dig teeth, sprockets, chain rollers, bearings, bushings etc. are 
excluded unless it can be determined that a defect has contributed to premature wear. 

 
 

   MAINTENANCE PREPARATION 

 
 
Only trained and qualified personnel should perform maintenance or repairs of the trencher. Before 
performing any service, maintenance, adjustments, repairs or off-season long-term storage, follow the 
SHUT DOWN PROCEDURE in the OPERATOR’S MANUAL.   
 

Do not touch the engine, muffler or any hydraulic components until cool.  

 

WARNING

: Muffler and engine may be hot enough to cause serious 

burns. For the safety of yourself and others, allow enough time for the 

engine, muffler and hydraulic fluid to cool completely before performing any 
cleaning or maintenance. 
 

Avoid contact with hydraulic fluid. 

 

WARNING

: When machine is operating, hydraulic fluid is under extreme pressure and can get 

under skin and burn or poison.  
 

 

 
 

Summary of Contents for 712MT
















Reviews: