Baroness LM551B Owner'S Operating Manual Download Page 35

Page: 35 / 172

Pull up the radiator cover to remove it.

va4j43-016

Cleaning of Radiator_002

Radiator cover

Unlock the rubber catches on the left and
right of the oil cooler, and then tilt the oil
cooler.

va4j43-017

Cleaning of Radiator_003

Rubber catch

Oil cooler

Radiator

Carefully clean the radiator with water or
compressed air.
Open the hood.

va4j43-018

Cleaning of Radiator_004

Hood

Radiator

Carefully clean the radiator with water or
compressed air.

Coolant

Inspection of Coolant

Caution

Do not touch the radiator or coolant during
engine operation or immediately after the
engine has been turned off.
Otherwise, you may get burned.

Caution

Inspection should take place after the engine
has well cooled down.

Make sure that the coolant level in the
reserve tank is between "FULL" and
"LOW".

v2x572-003

Inspection of Coolant_001

Reserve tank

Handling Instructions

LM551B

Handling Instructions

Page 4-5

Daily Check List

Summary of Contents for LM551B













































































































































































Search results

Summary of Contents for LM551B

Reviews:

Related manuals for LM551B

Brands by name

Popular brands

Baroness LM551B, Owner'S Operating Manual

Search results

Summary of Contents for LM551B

Reviews:

Related manuals for LM551B

Brands by name

Popular brands