manualshive.com logo in svg

Baroness LM551B, Owner'S Operating Manual, Page: 26 / 172

Share
Download
Baroness LM551B Owner'S Operating Manual Download Page 26

Description of Safety Decals and

Instruction Decals

Decal for Operation (E5)

STICKER, OPERATION (E5)
LM551B-0604Z0

　

Warning

Read the Owner's Operating Manual.

　

Warning

Apply the parking brake, stop the engine,
remove the ignition key, and then leave the
machine.

　

Caution

Flying objects - Be sure that people around
the machine keep a safe distance away.

　

Warning

May cut your hand or leg - Keep hands and
feet away from moving parts.

　

Warning

Be careful of exhaust emissions.

1.

2.

3.

4.

5.

　

Caution

Rollover - Do not work on slopes of 15
degrees or more.
When you descend a slope, lower the mower
units and then drive at low speed.
For ROPS equipped machine, fasten your
seatbelt.

1

2

5

6

3

4

myljsv-001

Decal for Operation (E5)_001

Caution to Rotating Object Decal

K4205001530
Decal, caution to rotating object

Warning

Watch for rotating parts - Keep your hands
away from the belts while the engine is
running.

qwsqzx-001

Caution to Rotating Object Decal_001

6.

LM551B

Product Overview

Page 3-10

Safety Signs and Instruction Signs

Summary of Contents for LM551B













































































































































































Reviews:

No comments