Baroness LM331 Owner'S Operating Manual Download Page 68

Precautions for Maintenance

Warning

The chapter "Maintenance" in this manual
describes practical measures which should be
performed by a mechanic with expertise.
The owner should instruct the mechanic with
expertise to perform maintenance service for
this machine.

Caution

First, learn well the operations you plan to
perform.

Important

Use tools appropriate for each operation.

Important

Use Baroness genuine parts for replacement
and accessories.
Our product warranty may be void if you use
non-genuine parts for replacement or
accessories.

Jacking Up The Machine

About Jacking Up The Machine

Warning

When replacing a tire or beginning any other
maintenance or repairs, be sure to chock the
wheels to prevent the machine from moving.
Before jacking up the machine, park it on a
hard, flat surface such as a concrete floor and
remove any obstacles that could prevent you
from performing the work safely.
When necessary, use an appropriate chain
block, hoist, or jack.
Support the machine securely with jack stands
or appropriate blocks.
Failure to do so may cause the machine to
move or fall, resulting in injury or death.

Important

Only place a jack under the jack-up points
specified.
Placing a jack at any other point will result in
damage to the frame or other parts.

Use the jack-up points identified in this manual
when jacking up the machine.

Jack-up Points

4

1

3

2

rwyt62-092

Jack-up Points_001

 

Jack-up Points

1

Front right frame

2

Front left frame

3

Rear right frame

4

Rear left frame

LM331

Maintenance

Page 6-2

Precautions for Maintenance

Summary of Contents for LM331








































































































Reviews: