Baroness LM285, Owner'S Operating Manual, Page: 33 / 65

Nominal
diameter
Heat-treated screws
Strength category: 8.8 Strength category: 10.9
8 T
8.8
8
tib3yb-002
11T
10.9
11
tib3yb-003
N-m kgf-cm lb-in N-m kgf-cm lb-in
M5 5 - 7 50.99 - 71.38 44.26 - 61.96 7 - 10 71.38 - 101.97 61.96 - 88.51
M6 8 - 11 81.58 - 112.17 70.81 - 97.36 14 - 18 142.76 - 183.55 123.91 - 159.32
M8 23 - 29 234.53 - 295.71 203.57 - 256.68 28 - 38 285.52 - 387.49 247.83 - 336.34
M10 45 - 57 458.87 - 581.23 398.30 - 504.51 58 - 76 591.43 - 774.97 513.36 - 672.68
M12 67 - 85 683.20 - 866.75 593.02 - 752.34 104 - 134 1,060.49 - 1,366.40 920.50 - 1186.03
M14 106 - 134 1,080.88 - 1,366.40 938.21 - 1,186.03 140 - 188 1,427.58 - 1,917.04 1,239.14 - 1,663.99
M16 152 - 188 1,549.94 - 1,917.04 1,345.35 - 1,663.99 210 - 260 2,141.37 - 2,651.22 1,858.71 - 2,301.26
M18 200 - 240 2,039.40 - 2,447.28 1,770.20 - 2,124.24 280 - 340 2,855.16 - 3,466.98 2,478.28 - 3,009.34
M20 245 - 295 2,498.27 - 3,008.12 2,168.50 - 2,611.05 370 - 450 3,772.89 - 4,588.65 3,274.87 - 3,982.95
M22 − − − 530 5,404.41 4,691.03
M24 − − − 670 6,831.99 5,930.17
M27 − − − 1,000 10,197.00 8,851.00
M30 − − − 1,340 14,628.78 11,860.34
Note:
The above values also apply for fine screw threads.
Principal tightening torques
Tightening Torque by Model
LM285
Tighten the following bolts and nuts at the torque specified in the table.
For thread locking adhesive, apply a middle strength thread locker (ThreeBond 1322 anaerobic
adhesives).
Portion Code Part name
Tightening torque
Thread locking
adhesive
N-m kgf-cm lb-in
Fron
t wh
ee
l Motor K0013120602
Bolt, 11T, heat-treated
M12-60 104
–
134
1,060.49
–
1,366.40
920.50
–
1,186.03
－
Wheel mounting
base
K0160000492 24 special nut P1.5
180 –
200
1,835.46 –
2,039.40
1,593.18 –
1,770.20
○
Wheel K0034120302
Bolt, 8T, heat-treated
M12-30P1.5
67
–
85
683.20
–
866.75
593.02
–
752.34
－
Rear
wheel
Wheel mounting
base
K0138240002 24 slotted nut high P1.5
180 –
200
1,835.46 –
2,039.40
1,593.18 –
1,770.20
－
Wheel K0034120302
Bolt, 8T, heat-treated
M12-30P1.5
67 – 85
683.20
–
866.75
593.02
–
752.34
－
Tie rod
K1610000020 Tie rod end right ass'y 45 158.87 398.30
－
K1611000020 Tie rod end left ass'y 45 158.87 398.30
－
Lever damper K0144080002 8U nut
— — — ○
Engine K0017100252
Bolt, heat-treated, small,
10-25 P1.25
45 – 57
158.87
–
581.23
398.30
–
504.51
－
Han
dlin
g Instru
cti
ons
LM285
Handling Instructions
Page 4-13
Tightening torques